Whats App
Annotated sling components

Oct 30, 2026

Chain Sling Specifications Explained: Grade 80 vs Grade 100, WLL and Lifting Capacity

Two chain slings can look identical and still carry very different loads. The tag tells them apart, and reading it correctly is the first step of every safe lift. This guide explains the chain sling specification in plain terms. You get a Grade 80 and Grade 100 comparison, a lifting chain capacity chart, angle factors for multi leg slings and a checklist for 4 leg slings. Use it when you raise an enquiry, review a quotation or check a sling that reaches your plant. Every section closes with a rule you can apply at the yard or on the shop floor, so the numbers stay practical.

Key Takeaways

  • Read the tag first: grade, chain diameter, WLL, angle range, length and serial number.
  • Grade 100 carries about 25 percent more WLL than Grade 80 at the same chain size.
  • Never mix grades inside one sling.
  • Leg angle and leg count change the rating more than most buyers expect.
  • A 4 leg sling takes a 3 leg rating on rigid loads.

What a Chain Sling Specification Contains?

Every certified chain sling carries a tag, and that tag is the specification in short form. It lists the chain grade, chain diameter, WLL for each leg configuration, the permitted angle range, the sling length and a serial number that links to the test certificate. A sling with a missing or unreadable tag leaves service until the manufacturer replaces it.

A complete chain sling specification covers five components:

  • Chain: diameter and grade set the base WLL of every leg.
  • Master link: joins all legs to the crane hook and must carry the combined load.
  • Hooks: grip the load and must match the grade of the chain.
  • Connecting links: join the chain to the master link and the hooks.
  • Shorteners: adjust leg length so the load sits level.

The weakest component sets the rating of the whole sling, so every part must match the grade and size of the chain. RUD India offers each part through its Chain Slings, Master Links, Hooks and Shorteners ranges.

Grade 80 vs Grade 100 Chain Slings

The grade number tells you the strength class of the chain. Grade 8 is the long established class under EN 818, with a nominal stress of 800 N/mm². Grade 10, which the market calls Grade 100, reaches 1,000 N/mm² and follows the DGUV principles that build on EN 818. RUD India offers chain slings in both grades.

At the same chain diameter, Grade 100 carries about 25 percent more WLL than Grade 80. RUD’s VIP range reaches up to 30 percent more. That extra capacity lets you drop one chain size.

Take a 3.5 tonne single leg lift. Grade 80 needs a 13 mm chain, which carries 5.3 tonnes. Grade 100 handles it with a 10 mm chain, which carries 4.0 tonnes. In RUD’s VIP range, the 10 mm chain weighs 2.45 kg per metre and the 13 mm chain weighs 4.04 kg per metre. Riggers feel that gap on every lift, and hoists feel it on every cycle. A smaller chain also brings smaller hooks and master links across the sling, which trims the weight your crew handles at every hitch.

Grade 80 still makes sense on fleets where every hook and link is already Grade 80, and on lifts where handling weight does not matter. Many plants run mixed fleets for years, so check which grade your existing slings use before you reorder.

One rule applies to both grades: never mix grades in one sling. A Grade 100 hook on a Grade 80 chain still leaves you with a Grade 80 sling, and a tag that shows anything higher is wrong.

Point of comparison Grade 80 Grade 100
Strength class 800 N/mm² 1,000 N/mm²
WLL at 13 mm, single leg 5.3 tonnes 6.7 tonnes
Chain size for a 3.5 tonne single leg 13 mm 10 mm
Best fit Existing Grade 80 fleets New slings and weight sensitive lifts

 

Also, Read: Safety Tips for Using Chain Slings

Working Load Limit (WLL) Explained

WLL is the maximum mass a sling can lift in service. Breaking load is the force that destroys the chain in a test. Chain slings use a 4:1 design factor, so the breaking force sits at least four times above the WLL. SWL is the older term on many tags, and current standards use WLL.

Four conditions cut the usable capacity of a sling:

  • Leg angle: wider angles raise the tension in every leg.
  • Hitch type: a choke hitch cuts the WLL to 80 percent of the rated figure.
  • Temperature: heat above the rated range reduces WLL. The heat FAQ on the Chain Slings page lists the figures.
  • Shock loading: snatch, drop and sudden starts load a sling well above the weight of the load.

Treat the WLL as a ceiling for a smooth, controlled lift, never as a target. Always read the WLL for your own leg configuration, since the tag lists a separate figure for each.

Lifting Chain Capacity Chart (Single Leg)

This lifting chain capacity chart lists single leg WLL in tonnes by chain diameter for Grade 80 and Grade 100. Every multi leg rating in this guide builds on these numbers.

Chain diameter (mm) Grade 80 WLL (tonnes) Grade 100 WLL (tonnes)
6 1.12 1.5
8 2.0 2.5
10 3.15 4.0
13 5.3 6.7
16 8.0 10.0
20 12.5 16.0
22 15.0 20.0

 

How to read the chart:

  1. Find your chain diameter in the first column. This is the nominal diameter of the bar that forms each link.
  2. Read the WLL under Grade 80 or Grade 100.
  3. Multiply that figure by the leg factor in the next section when you use a multi leg sling.

A 16 mm Grade 80 chain carries 8.0 tonnes in a single leg, while the same diameter in Grade 100 carries 10.0 tonnes. Check every figure against the sling tag before you lift.

Chain diameter drives capacity faster than most buyers expect. Compare 10 mm and 13 mm Grade 100 chain: the 13 mm chain carries 6.7 tonnes against 4.0 tonnes for the 10 mm chain, a gain of about 68 percent. Capacity follows the cross section of the link, so each size up adds more than the last. Use the chart to find the smallest chain that covers your load, then weigh that chain against the lift you plan. A chain one size too large adds cost and handling weight for every rigger on the crew. Remember that this chart covers a straight single leg pull only.

Also, Read: Types of Chain Sling

Chain Working Load Limit Chart by Leg Configuration and Angle

Multi leg slings carry more than single leg slings, but only while the legs stay inside their angle band. This chain working load limit chart gives the factor for each configuration. Multiply the single leg WLL by the factor to get the sling WLL. The 13 mm column shows the result.

Configuration Angle from the vertical Factor Grade 80, 13 mm (tonnes) Grade 100, 13 mm (tonnes)
1 leg Straight pull 1.0 5.3 6.7
2 leg Up to 45 degrees 1.4 7.4 9.4
2 leg Over 45 to 60 degrees 1.0 5.3 6.7
3 and 4 leg Up to 45 degrees 2.1 11.1 14.1
3 and 4 leg Over 45 to 60 degrees 1.5 8.0 10.1
Endless Basket hitch 1.6 8.5 10.7

 

Check which angle the chart uses. Some charts measure the leg against the vertical. Others measure it against the horizontal. A leg at 30 degrees above the horizontal sits at 60 degrees from the vertical. Mix the two up and you rate a 2 leg sling at 1.4 times its single leg WLL when it really earns 1.0, which overloads each leg by about 40 percent. This guide measures from the vertical, as EN 818-4 does.

Working example: a 10 tonne load on a 2 leg sling with legs at 45 degrees. The factor is 1.4, so each leg needs a single leg WLL of at least 7.14 tonnes. Grade 80 needs a 16 mm chain, and the sling then carries 11.2 tonnes. Grade 100 also lands on 16 mm, because the 13 mm chain at 6.7 tonnes falls short. The 16 mm Grade 100 sling carries 14.0 tonnes. Drop the load to 9 tonnes and Grade 100 in 13 mm covers it at 9.4 tonnes, while Grade 80 still needs 16 mm. Run this check for every lift before you order, because the right size changes whenever the angle or the load changes. When a result lands between two sizes, move up one size, never down.

4 Leg Chain Sling Specification

A 4 leg chain sling carries the same rating as a 3 leg sling of the same chain. On a rigid load, such as a fabrication or a machine base, the legs never share the weight equally. Small differences in leg length and hook height let one leg go slack while the other three take the load. The rating assumes three working legs.

Chain diameter (mm) Grade 80, up to 45 degrees Grade 80, over 45 to 60 degrees Grade 100, up to 45 degrees Grade 100, over 45 to 60 degrees
10 6.6 4.7 8.4 6.0
13 11.1 8.0 14.1 10.1
16 16.8 12.0 21.0 15.0

 

All figures show sling WLL in tonnes. The fourth leg adds stability, not capacity, so specify a 4 leg sling for balance and never to gain rating. Use this checklist when you write the 4 leg chain sling specification:

  • Grade: one grade for every component.
  • Chain size: sized from the 3 leg factor, never four times the single leg WLL.
  • Reach: the effective working length between the master link and the hook.
  • Master link size: wide enough for the crane hook and strong enough for the combined load.
  • Hook type: matched to the pick points and fitted with a latch.
  • Angle range: the smallest and largest leg angle you expect on site.
  • Certification: the test certificate the lift requires.

Choose a spreader beam when the load is long, fragile or sensitive to inward pull, or when low headroom forces the legs past 60 degrees from the vertical. A spreader beam keeps the legs close to vertical, so chain tension stays low and the load takes no sideways squeeze. The 4 leg FAQ on the Chain Slings page and the Spreader Beam page cover the choice in more detail.

Specification Errors RUD India Engineers See in the Field

  1. Rating four legs as four working legs. The buyer multiplies the single leg WLL by four and orders a sling that is too light. A 4 leg sling never carries four times the single leg WLL. The correct specification uses the 3 leg factor.
  2. Reading the chart from the wrong reference angle. A wide leg angle gets rated in the narrow band, and one band of error overloads each leg by about 40 percent. The correct approach confirms whether the chart measures from the vertical or the horizontal and keeps legs within 60 degrees from the vertical.
  3. Fitting a hook of another grade to match stock. The sling drops to the rating of the lower grade. The correct specification keeps one grade and one tag.
  4. Ordering by chain size alone. The sling arrives too short for the lift, and the crew spreads the legs wider to compensate. The correct specification states reach, hook height and angle range.

How to Choose the Right Chain Sling?

Work through five steps in order:

  1. Load weight and centre of gravity: confirm both before you pick a size.
  2. Pick points: count them, locate them and check their rated capacity.
  3. Leg angle: keep legs within 60 degrees from the vertical.
  4. Environment: note heat, chemicals, sharp edges and outdoor exposure.
  5. Grade: choose Grade 100 for weight savings or Grade 80 to match an existing fleet.

Temperature needs its own check. Chain keeps its full WLL between minus 40 and 200 degrees Celsius. Above that, WLL drops in steps, and Grade 100 loses capacity faster than Grade 80 in the hottest band. Foundries, forging shops and steel plants should read the heat FAQ before they order.

Inspect the sling before every use. The maintenance FAQ covers the full routine. At minimum, check that:

  • the tag is legible
  • links show no stretch, nicks, gouges or twisting
  • hook latches close and the throat shows no opening
  • the master link shows no wear or deformation

Avoid the common mistakes: guessing the load weight, ignoring the angle, mixing grades, overlooking temperature and skipping the tag check.

Also, Read: Proper Use of Chain Slings

Standards Referenced and Safety Note

This guide draws on EN 818-2 for chain, EN 818-4 for chain slings and the DGUV principles RUD uses to certify Grade 100.

Final sling selection must be verified against the sling tag, the manufacturer’s certificate and a competent person’s lift plan. This guide is for understanding, not a substitute for a lift plan.

Conclusion

Three factors decide a chain sling specification: grade, leg angle and leg count. Grade sets the base WLL for each chain size. Leg angle decides how much of that capacity your lift keeps. Leg count decides the factor you apply, and a 4 leg sling still counts as a 3 leg sling on a rigid load. Get those three right and the rest of the specification falls into place. Share your load weight, pick points, angle range, environment and required certificate with RUD India’s engineers, and they will recommend the right sling. Contact RUD India today.

Frequently Asked Questions

Not always. Grade 100 gives about 25 percent more WLL at the same chain size, so it suits most new purchases and saves weight. Grade 80 stays sensible when your hooks, links and fittings are already Grade 80, because one sling cannot mix grades safely.

Avoid it. A Grade 100 hook adds no capacity to a Grade 80 chain, because the sling takes the rating of the lower grade. A mixed assembly also risks a tag that overstates capacity. Specify every component in one grade from one matched system.

Keep each leg at least 30 degrees above the horizontal, which equals 60 degrees from the vertical. Wider spreads raise leg tension sharply and fall outside the rated bands. At 30 degrees above the horizontal, each leg of a 2 leg sling carries the full weight of the load.

Similar Posts

By Admin   |   Mar 27, 2023

Coil Tong: A Tool for Efficiently Handling Coiled Materials

slider-arrow-black.pngslider-arrow-pink.png

By Admin   |   Apr 04, 2023

The Role of Drag Chain Conveyors in Automated Material Handling Systems

slider-arrow-black.pngslider-arrow-pink.png

By Admin   |   May 02, 2023

3 Essential Tips for Safe and Effective Use of Plate Clamps

slider-arrow-black.pngslider-arrow-pink.png