Whats App
RUD India lifting attachments for safe excavator component handling

Oct 30, 2026

Safe Lifting of Excavator Components Using Engineered Lifting Attachments

Excavator components are heavy, awkwardly shaped and rarely built for a convenient lift. During maintenance or assembly, crews still lift them with whatever gear sits in the workshop. This guide covers lifting parts of an excavator, such as booms, counterweights and swing bearings. It does not cover using an excavator as a crane. You will see which components need engineered excavator lifting attachments, why improvised rigging fails and how to select the right attachment for the job. Each section ends with something your team can act on this week. The advice suits any plant that services heavy earth moving equipment, including rental fleets and mine workshops.

Key Takeaways

  • Every major excavator component has its own weight, balance point and attachment points.
  • Take weights from the OEM manual for your exact model, never from memory.
  • Slinging round parts or welding unrated eyes puts a lift outside any rating.
  • Match the attachment to the load: lifting points, chain slings, spreader beams or tilters.
  • Inspect lifting gear before each use and keep a competent person’s lift plan on file.

Which Excavator Components Need Engineered Lifting?

Excavator component handling changes with every part. The table shows where the lifting challenge sits for each one. Weights vary widely between machine classes, so read the figure for your model from the OEM manual.

Component Typical lifting challenge
Boom Long member with an off centre balance point that shifts once cylinders and hoses go on
Stick Weight sits toward the bucket end, with few places to attach gear
Bucket Weight depends on size and wear parts, and the balance point moves with teeth and side cutters
Counterweight One of the heaviest single pieces, compact, with attachment points set by the OEM
Track frame Wide and unbalanced, with rollers and idlers adding mass at uneven spots
Final drive Heavy for its size, with limited attachment points on the housing
Swing bearing Large flat ring that needs several even pick points to stay level
Engine and pump Heavy, irregular and packed into a tight bay with the balance point off centre

 

For scale, the Caterpillar 336 specification sheet lists its counterweight at 7,560 kg and its 2.27 cubic metre general duty bucket at 1,590 kg.

Why Improvised Lifting Fails?

Improvised lifting looks quick until a load shifts. Five failure modes recur:

  • Round parts with no rated point: A sling around a smooth cylinder grips by friction alone and can slide as the load moves.
  • Unknown welded eyes: An eye welded on in the yard has no rating, no test record and no check on the metal beneath it.
  • Wrong centre of gravity: A pick above the wrong spot tilts the part as it leaves the ground, and one leg takes far more than its share.
  • Side loading on lifting points: Many points carry their rating only along a defined direction, so a sideways pull cuts what they can hold.
  • Damaged or unmatched gear: Worn slings, bent hooks and mixed grades carry less than the tag claims.

Heavy lifting equipment safety starts with a rated point of attachment, a known weight and gear that matches. Remove any one of those three and the rest of the setup stops mattering. Engineered attachments close each gap.

Also, Read: Tips for Handling Heavy Loads With Lifting Equipment

Excavator Lifting Attachments That Do the Job

The right excavator lifting attachments give you a rated point, a rated connection and a controlled path for the load. RUD India supplies five types that cover most maintenance lifts on earthmoving equipment.

Attachment Type What It Solves RUD India Page
Bolt-on lifting points (load rings, PowerPoint, STARPOINT, TURNADO) Gives a rated attachment point in a threaded hole, where the OEM allows it, so nobody guesses Lifting Points
Weld-on lifting points (ABA, VRBS and VLBS load rings) Gives a rated point on fabricated frames and shop fixtures. Never weld to an OEM component without OEM approval Lifting Points
Chain slings with shorteners Connect the points to the crane hook, and the shorteners level a part whose balance point sits off centre Chain Slings
Spreader beams (loop, H frame, heavy lift, customized) Keep legs near vertical on long or wide parts such as booms and track frames, and cut the squeeze on the load Spreader Beam
RUD Equip Tilter Tilts a heavy assembly to a working angle in the maintenance bay, with one operator and automatic locking RUD Equip Tilter

 

Most maintenance lifts combine two or three of these types. A rated point sits on the component, a chain sling carries the load to the crane hook and a spreader beam joins the setup when the part is long or the headroom is tight. A customized spreader beam suits parts that fit no standard beam, and a drawing with the OEM weight gives the design team what it needs.

Pick the attachment by the load, not by what sits nearest on the rack. RUD India’s engineers can match ratings to your OEM data.

How to Select the Right Attachment?

Work through six checks before you rig:

  • Load weight and centre of gravity: Take the OEM figure for your model and locate the balance point.
  • Attachment points: Use the OEM points first, since the manufacturer tested them for that part, and confirm their rating.
  • Direction of pull: Keep the pull inside the direction the point allows.
  • Rated WLL: Size every leg and component for the load at its working angle.
  • Environment: Mud, dust and heat all reduce what gear can do, so check the rated range and clean the gear first.
  • Certification: Confirm test certificates and legible tags before the lift.

Worked example: The Caterpillar 336 counterweight weighs 7,560 kg according to the specification sheet. Assume two lifting points and a 2 leg sling with legs at 45 degrees from the vertical. The factor is 1.4, so each leg needs a single leg WLL of at least 5.4 tonnes, before you add the weight of the sling and shackles. A 13 mm Grade 100 chain carries 6.7 tonnes and clears the load. A 13 mm Grade 80 chain carries 5.3 tonnes and falls short, so it needs 16 mm. Confirm the real lifting point layout and rating in the OEM manual first.

Also, Read: Benefits of Using High-Quality Lifting Points

Lifting During Earthmoving Equipment Maintenance

Earthmoving equipment maintenance runs in cycles: scheduled overhauls, component swaps and repairs. Each stage brings lifts, so plan the gear with the maintenance schedule, not on the morning of the job.

Run this pre-lift checklist every time:

  • Weight confirmed from the OEM manual for the exact model
  • Attachment points identified, rated and free of damage
  • Sling tag legible and WLL above the load at the working angle
  • Leg angle inside the rated band
  • Lift plan agreed with a competent person
  • Area below the load cleared

Inspect gear before every lift, and arrange a thorough examination by a competent person at the interval your regulations and the manufacturer set. Tag out damaged gear the moment you find it, so nobody picks it up again.

Keep a log for every sling and lifting point, with its tag number, inspection date and result. The log shows wear before it becomes a failure. Store gear on racks away from mud and cutting torches, because weld spatter and corrosion damage chain and fittings.

A Real Application From RUD India

RUD India supplied a RUD Equip Tilter for Caterpillar. The project record lists the configuration as 40 T x 12 m, with two units at 4 T self weight each, 8 T in total.

The tilter pivots a load around a fixed point using a RUD TECDOS chain and pocket wheel. One operator runs it from a wired control or an optional radio remote. It indexes at any angle and locks automatically, so the load stays where the crew set it. Integrated lift points let a crane or forklift move the unit between bays and sites, and tool-free access panels make inspection quicker. The design suits maintenance bays, assembly lines and remote job sites, which matches how earthmoving equipment workshops operate.

Standards and Safety Note

Relevant standards include EN 13155 for non fixed load lifting attachments, ASME B30.20 for below the hook lifting devices, EN 818 for chain slings and [Indian standard references to be supplied by RUD India technical team].

Final selection needs OEM guidance, a rated attachment and a competent person’s lift plan. This guide is for understanding, not a substitute for the OEM manual or a lift plan.

Conclusion

  • Know the weight and balance point from the OEM manual.
  • Attach through a rated point, never an improvised one.
  • Match the attachment to the load and to your maintenance bay.
  • Share the component, its weight, the lifting points and your site conditions with RUD India’s engineers, and they will recommend the right excavator lifting attachments. Include the OEM model number and any drawing you have, so they can size the attachment against real data. Contact RUD India today.

Frequently Asked Questions

Not always. Grade 100 gives about 25 percent more WLL at the same chain size, so it suits most new purchases and saves weight. Grade 80 stays sensible when your hooks, links and fittings are already Grade 80, because one sling cannot mix grades safely.

Avoid it. A Grade 100 hook adds no capacity to a Grade 80 chain, because the sling takes the rating of the lower grade. A mixed assembly also risks a tag that overstates capacity. Specify every component in one grade from one matched system.

Keep each leg at least 30 degrees above the horizontal, which equals 60 degrees from the vertical. Wider spreads raise leg tension sharply and fall outside the rated bands. At 30 degrees above the horizontal, each leg of a 2 leg sling carries the full weight of the load.

Similar Posts

By Admin   |   Mar 27, 2023

Coil Tong: A Tool for Efficiently Handling Coiled Materials

slider-arrow-black.pngslider-arrow-pink.png

By Admin   |   Apr 04, 2023

The Role of Drag Chain Conveyors in Automated Material Handling Systems

slider-arrow-black.pngslider-arrow-pink.png

By Admin   |   May 02, 2023

3 Essential Tips for Safe and Effective Use of Plate Clamps

slider-arrow-black.pngslider-arrow-pink.png